Location:
Search - JLINK v4
Search list
Description: JLink Software and documentation pack V3.96b -JLink Software and documentation pack V3.96b
Platform: |
Size: 7230464 |
Author: danny |
Hits:
Description: Jlink for ARM 仿真器的驱动程序-Jlink for ARM emulator driver
Platform: |
Size: 7695360 |
Author: andy |
Hits:
Description: hardware:
1.CPU:S3C2440A
2.norflash:2MB,bank0, 16bit
3.SDRAM: 64MB,bank6
4.Nandflash:256MB, 8bit
5.develop broad:TX2440A (V6.2 2011/05/12)
6.Jlink v8
software:
1.Jlink v4.08
2.MDK 4.23
Platform: |
Size: 677888 |
Author: 水中林 |
Hits:
Description: 写给入门级STM嵌入开发者的STM32F107+Keil v4.12+jlink v8在SRAM环境中调试程序设置，详细介绍了KEIL环境下对ROM和RAM的地址设置-For entry-level STM embedded developer STM32F107+Keil v4.12+jlink V8 in the SRAM environment debugging program, introduced in detail the KEIL environment for ROM and RAM address set
Platform: |
Size: 167936 |
Author: 黄云 |
Hits:
Description: 使用新版本的J-link驱动，版本在V4.50以后的，打开 J-Link ARM或者从KEIL MDK里面选择Debugger为J-LINK / J-Trace Cortex后点Setting时，会提示J-Link为Clone，然后自动关闭。
本文在网上搜集了许多解决办法，并且经过实践挑选出最为有效和完美的解决办法，整理成了一个教程。对于这些方法的原作者，表示感谢。
-A good tutorial to flash the not-working Jlink V8
Platform: |
Size: 7905280 |
Author: 李玉尧 |
Hits:
Description: jlink v4.10i.zip jlink setup -jlink v4.10i.zip
Platform: |
Size: 8337408 |
Author: jimmy |
Hits:
Description: 使用外设：串口线一跟，通过COM1连接PC
** 实验名：【B】USART_TEST
** keil MDK-ARM Standard Version：V4.22A
** 软件库(keil) Version: V2.0.1
** 固件库(ST) Version: V
*************************************/
/***********************************
** 实验现象：
1、首先进行常规配置(RCC、NVIC、GPIO)，然后配置串口1(115200baud 8位数据位 1位停止位 无奇偶校验位)
2、通过对USART1写操作，完成了向PC发送字符串的功能
3、此实验对串口的操作都是通过调用ST固件库，
** 实验说明：
1、打开超级终端，进行相同的设置
2、通过JLINK烧写程序，按下“RESET”键，可以看到PC接收到的字符串
“welcome to STM32”(using peripherals: the serial port line is a heel, and the PC is connected to the COM1
* * * experimental Name: [B] USART_TEST
* * * keil MDK-ARM Standard Version:V4.22A
* * software library (keil) Version: V2.0.1
* * firmware library (ST) Version: V
*************************************/
/***********************************
* * experimental phenomena:
1, first of all the regular configuration (RCC, NVIC, GPIO), and then the serial port 1 (115200baud 8 bit data bit, 1 bit stop bit and no parity bit)
2. By writing to USART1, the function of sending strings to PC is completed
3. The operation of this experiment on the serial port is by calling the ST firmware library.
* * the experiment shows that:
1. Open the super terminal and make the same setup
2, through the JLINK burning program, press the "RESET" key, you can see the string received by PC
Welcome to STM32)
Platform: |
Size: 653312 |
Author: 72521
|
Hits: